0101 147 0331

تواصل معنا 24 ساعة في اليوم، 7 أيام في الاسبوع

Technology

Revitalization — "bringing back to life"

The word revitalization (latin. vita — life) can be literlly interpreted as "bringing back to life". The discovery of the revitalization phenomenon is based on the unique physical and chemical processes as a result of friction which occurs under specific conditions.

In brief, the essence of the phenomenon is as follows: when a mechanism is operating, stress is formed on the friction surfaces. Under high load excessive thermal energy is released destroying and wearing parts.

However, if a unique building material — revitalizant is introduced to the friction area, it converts the excessive energy to form a new coating. Therefore from friction's destructive energy positive conditions are formed. The energy of destructions turns into the energy of creation!

 

Wear and tear of the operating surface

In order for a defect to occur it is enough to have a scratch or a chip emerged due to impact of solid foreign particles (dust, dirt or cutting waste). This area becomes a zone of enormous surface activity. It appears in places where metal atoms have uncompensated connections. So they can be easily “loosened” and torn from the matrix when the load increases. Metal starts chipping.

 

Start of the revitalization process

The revitalizant gets onto the operating surface together with the lubricant. The revitalizant starts acting exactly in the zone of the heaviest wear, as there is enough excess energy here to start to start the revitalization process, and metal atoms possess the largest number of uncompensated connections. These connections, like magnets, capture and hold the building material, revitalizant, just in the areas of wear and tear.

 

New coating formation

In a few minutes after beginning of the revitalization process a ceramic-metal patch appears in the place where a scratch was. The zone of enormous activity disappears. The energy processes stabilize, the growth of the ceramic-metal coating stops.

 

Completion of the surface modification

Due to diffusion of the protective layer into metal an extremely firm gradient ceramic-metal coating with unique operating properties is created.

 

Revitalization results

The potential of revitalization has changed the modern conception of vehicle and machinery operation and repair. XADO products have created a hightech and yet very simple method to reverse the wear.

As a result of revitalization a new coating is formed on the surface of the friction pairs — a part builds up and restores its geometry. The new coating possesses unique properties: an amazing durability (microhardness 650–750 kg/mm2), high corrosion resistance, and a very smooth surface (Ra up to 0.06 micron). That is why a part is guaranteed to last by up to 2–4 times longer after the revitalization. The revitalized mechanism will also be indebted to you and will continue to operate at its best!

The benefit of the revitalization is that you will end up with a mechanical assembly which will perform better than new and which will last longer than it would have done!

 

Benefits of revitalization

Repair and Restoration of Assemblies. New metalloceramics coating is formed on the friction pairs; these parts increase in weight and volume, and restore their initial geometry (the biggest increase is up to 1.5 mm!). The restoration occurs during normal mechanical operation so that the ideal fit of the friction pairs is achieved. As a result, the capacity of power units increase, the accuracy of the mechanism work improves, and noise and vibration are reduced.

Resources saving, significant reduction in the amount of assembly wear and tear. After revitalization the new coating possesses unique properties: amazing durability (micro-hardness 650–750 kg/mm2) and high corrosion resistance. It helps to prevent from further metal loss, to maintain an ideal friction surface and significantly increase the reliability of the assembly, to prolong their life span.

Power and energy saving. Another advantage of the metalloceramics coating is an abnormally low friction factor (roughness Ra up to 0.06micron). After treating the friction surfaces, it results in a significant increase (up to 30%) in energy saving.

Ecological rationality. The saving of energy and resources is the basic for environment protection. When a revitalized mechanism is operating, there is a significant reduction in the release of harmful exhaust substances (CO, CH, and NOx) to the atmosphere.

 

Demonstrably about the revitalization process

BEFOREapplicationof revitalizant
 Demonstrably about the revitalization process 
AFTERapplicationof revitalizantA real surface of a part beforeand after the revitalization.After 500 km (300 miles) of run the defect has been completely removed. As a result of revitalization a perfectly smoothed protective ceramic-metal coating has been formed on the surface of the part.

How does it work?

Demonstration experiment

  • The rolling path of a bearing has been damaged with the help of an engraving cutter. It should be noted that all the defects are being made with a reserve in their sizes, i.e. the defects are much larger than those which may occur on the surface of the part during its actual operation. Such a defect is a concentrator and may lead to destruction of the part. The bearing is filled with XADO Repairing Grease designed for heavily (up to 80%) worn units.

  • A fragment of the bearing’s rolling path. The initial factorymade surface is rough, with deep traces of a grinding tool. In the middle there is a point defect (a crater) especially made for the tests, with 0.5 mm diameter and up to 0.7 mm depth.

  • The operating bearing filled with the grease is being exposed to an 8000 N force at a rotation frequency of 1,000 rpm within 15 minutes. The revitalization itself takes place during operation of the bearing – it means elimination of the defect on the friction surface by creation of a protective ceramic-metal coating. The result of the experiment is shown on the pictures.

  • The same fragment of the bearing after 15 minutes of operation under load with XADO Repairing Grease. The surface is modified with ceramic metal, it is smooth and glassy. The traces of initial factory grinding have completely disappeared. The boarders of the crater are covered with some buildups resembling snow flushes at the edges of a ravine. It can be clearly seen that the elimination of the defect proceeds from the edges to the center of the crater while gradually filling it.

العودة إلى أعلى الصفحة